Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Enterprise Homeowners
Chimney repair in Enterprise comes down to one question: is the masonry, liner, cap and flashing on your roof still doing the three jobs they exist for? Those jobs are keeping water out, keeping combustion gases moving up and out, and holding sparks and embers away from anything that can burn. Once a crack or a rusted cap opens a path, all three start failing at once, and the damage usually spreads quietly until a sweep or inspection finds it. Our technicians have up to 13 years of experience working on wood-burning fireplaces, gas fireplaces and wood stoves, and they call out professional-grade parts by name: DuraFlex liners, HeatShield resurfacing, Gelco caps. We treat your chimney as a system, not a stack of unrelated parts. If something has shifted or cracked, call (855) 752-5896 and we’ll book a sweep and inspection. We answer 24/7, with fast dispatch from 7am to 7pm.
Chimney Cap Installation
Chimney Cap Installation is the fitting of a screened cap over the flue opening to keep rain, birds and debris out while letting smoke escape. You need it when a flue is open to the sky, when birds or squirrels have gotten in, or when a cap has gone missing entirely. We install Gelco caps sized to the flue, sealed to the crown so water runs off instead of wicking into the masonry. Expect a typical cap installation in Enterprise to run $180 to $450, depending on flue count and cap style. The written estimate sets the final price.
Why a Cap Matters More in the Desert
A dry climate doesn’t mean a dry chimney. Wind-driven dust and grit settle into an open flue, and one good rainstorm sends water straight down onto the smoke shelf and damper. A screened cap stops both without restricting draft.
Custom-Fit vs. Universal Caps
A universal cap usually leaves gaps around an irregular flue tile, and that gap invites birds. We measure the actual opening and specify a cap built for it, so the seal is snug and the screen holds up to heat and weather.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement is the removal of a failed cap and the fitting of a new one, most often because rust has eaten through the screen, the top has warped, or the cap has come loose and shifted off center. If your current cap rattles in wind or has visible rust holes, replace it before animals and water find the opening. We pull the old cap, check the flue tile and crown underneath for damage the old cap may have hidden, then set a new Gelco cap and seal it down. A chimney cap replacement in Enterprise typically falls between $200 and $500, depending on access and cap size. The written estimate is the final word on price.
Signs the Old Cap Is Finished
Rust-through on the mesh, a cap sitting crooked, or visible daylight between cap and flue all point to replacement rather than repair. Waiting lets water reach the flue tile, and that’s where costs climb.
Matching the Cap to the Appliance
A wood-burning flue needs a cap sized for its draft; a gas appliance has different venting needs. We check what’s connected before specifying a replacement, so the new cap doesn’t choke the draft.
Chimney Liner Installation
Chimney Liner Installation is the fitting of a new flue liner inside the existing chimney to contain heat and combustion gases for the full run from appliance to cap. You need it when the original clay tile is cracked, missing, or there’s no liner at all, which is common in older construction and after a chimney fire. We install DuraFlex flexible liner systems, a professional-grade line chimney specialists specify because it handles the offset and bends of a real flue. Liner installation in Enterprise usually runs $2,200 to $5,500, depending on height, flue size and whether insulation is added. A written estimate locks the number before any work begins.
Flexible vs. Rigid Liner
A straight flue can take rigid sections, while an offset or an older chimney often needs the flexible DuraFlex option. We scope the flue first so the liner type matches what’s actually up there.
Insulating the Liner
Insulation around a liner holds flue temperature up and reduces creosote buildup. On an exterior chimney it also helps the appliance draft properly, which matters more than most homeowners expect.
Chimney Flashing Repair
Chimney Flashing Repair is the fixing or replacing of the metal that seals the joint where the chimney meets the roof, the most common entry point for leaks. You need it when you see staining on the ceiling near the chimney, rust on the flashing itself, or gaps where the metal has pulled away from the masonry. We reset or replace the flashing, step it into the roofing, and seal it so water runs down the roof and around the chimney instead of into the attic. Flashing repair in Enterprise typically runs $300 to $900, depending on roof pitch and how much metal is replaced. The written estimate sets the final price.
How Leaks Start at the Joint
Two different materials, masonry and roofing, expand and contract at different rates. Over time that movement opens the seal. Left alone, water works into the framing around the chimney.
Flashing and Water Damage
Flashing leaks rarely announce themselves. Often the first sign is a damp spot on the ceiling or a musty smell in the attic. Catching it early keeps the repair small.
Chimney Crown Repair
Chimney Crown Repair is the fixing or rebuilding of the concrete top of the chimney, the sloped surface that sheds water away from the flue and masonry below. You need it when the crown is cracked, crumbling or pulling away from the flue tile, because a failed crown lets water soak into the brick and freeze-thaw cycles, even mild ones, keep working at it. We repair minor cracks or rebuild a badly damaged crown with a fresh, properly sloped pour. Crown repair in Enterprise usually runs $350 to $1,100, depending on the size of the crown and whether a full rebuild is needed. Your written estimate is the final price.
Reading the Cracks
Hairline surface cracks are normal. Wide cracks, a crown that’s separated from the flue, or spalling concrete are signs the crown needs real work, not a patch.
Why the Slope Matters
A crown should shed water rather than let it pool. A flatter-than-it-should-be crown holds water at the flue joint and speeds up deterioration.
Chimney Repair Companies
Chimney Repair Companies range from dedicated chimney specialists to general contractors who add chimneys to their list, and the difference shows in what they carry and what they know. You need a specialist company when a repair needs to match the system already on your roof or when a diagnosis could mean real money, and you want a second opinion you can verify. We work exclusively in the chimney trade, specifying Copperfield and Olympia Chimney supply-line parts, so nothing gets improvised from a big-box shelf. Expect a chimney repair in Enterprise to run $250 to $1,500 for common fixes, or more for liner and masonry work. The written estimate sets the final price.
Questions Worth Asking
Ask what brands a company specifies and why. Ask whether the person diagnosing your chimney is the same crew doing the work. Vague answers are a reason to keep looking.
Specialist vs. General Contractor
A general contractor may do fine structural work but not carry chimney-specific liners or resurfacing systems. That mismatch is where repairs get compromised.
Chimney Masonry Repair
Chimney Masonry Repair is the repair of the brickwork, mortar joints and chimney structure itself, from tuckpointing to rebuilding a section of stack. You need it when mortar joints are receding, bricks are spalling, or the chimney is leaning or has visible gaps. We repoint joints, replace failed brick and, where the flue interior needs resurfacing rather than rebuilding, apply HeatShield, a system designed to extend flue life instead of masking damage. Chimney masonry repair in Enterprise typically runs $500 to $2,500, depending on how much of the stack is involved. The written estimate sets the final price before the first brick is touched.
Tuckpointing vs. Rebuilding
Receding mortar gets repointed; loose, crumbling brick may need rebuilding in sections. The right call depends on how deep the damage runs.
Spotting Spalling Brick
Brick faces that flake or peel are failing from the inside, often because water is getting in somewhere above. Fixing the source comes first.
Brands We Service
We install and service DuraFlex flexible liner systems, and we know where the liner takes the most heat and where a joint is most likely to fail. We use HeatShield resurfacing technology for flue repair, a system built to extend the life of an existing flue rather than cover over the problem. Gelco chimney caps are our go-to for capping and replacement because they fit properly and hold up. Famco ventilation components and Copperfield specialty parts round out what we specify, so nothing on your chimney is a generic substitute.
Because we work the chimney trade only, our tooling and product knowledge stay focused there. We’re not a general contractor who also does chimneys, and we’re not a dealer pushing one brand. We specify what fits the job because it’s what professionals specify, and we service across these lines. Whether you have a DuraFlex, HeatShield, Gelco, Famco or Copperfield product, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Water stains on the ceiling or chimney breast. That’s usually flashing or crown failure letting water in. Catching it early keeps the repair small and prevents rot around the framing.
- Crumbling mortar or spalling brick. Receding joints and flaking brick mean the masonry is deteriorating from the outside in. Repointing now is far less costly than rebuilding later.
- A strong smoky smell or visible creosote. Heavy creosote buildup is a chimney fire waiting to happen. A sweep and inspection should come before the next fire.
- Cracks in the flue tile or a collapsed liner section. A compromised liner lets heat and gases reach the masonry, which is a genuine safety issue. This needs a professional look now.
- A loose, rusted or missing cap. An open flue invites water, birds and debris. A quick fix prevents bigger problems in the flue and firebox.
Our Process, Step by Step
- 1
Book the visit. A sweep and inspection are booked together so nothing gets diagnosed from a ladder at the curb. We confirm the appointment and come prepared for whatever the chimney needs.
- 2
Camera inspection and photo report. We run a camera down the flue and photograph what we find, from the crown to the firebox. You see the evidence, not a verbal claim.
- 3
Walk you through the findings. We show the photos and explain what’s a real safety issue and what can safely wait. Nothing is recommended without camera evidence you can see for yourself.
- 4
Written estimate before work. The price is set per job by the written estimate, so the number you approve is the number you pay. No surprises when the work starts.
- 5
Repair and final check. The same crew that diagnosed the problem does the work, then re-checks the fix. Sweep, repair and inspect come from one specialist, not three contractors.
How Much Does Chimney Repair Cost in Enterprise?
A typical chimney cap replacement in Enterprise runs $200 to $500, depending on access and cap size. Crown repair usually falls between $350 and $1,100, flashing repair between $300 and $900, and liner installation between $2,200 and $5,500 depending on flue height and whether insulation is added. Masonry work, from tuckpointing to a partial rebuild, typically lands between $500 and $2,500. For common repair calls that don’t involve a liner or masonry rebuild, most jobs run $250 to $1,500. These are estimates, and your written estimate is the final price.
What moves the number: how high the flue runs, how much of the stack needs work, whether the crown or flashing is fully replaced or just repaired, and whether a liner has to come out before the fix goes in. The biggest driver is doing nothing until a small issue becomes structural. A crack that could have been sealed can turn into a rebuild.
To avoid overpaying, ask for camera evidence of what actually needs fixing and get a written estimate before work starts. Nothing gets recommended without photo proof. If work can safely wait, we say so. Our free estimate includes the inspection findings, the line-item estimate and a plain explanation of what’s safety-critical versus cosmetic. Call us for an exact quote, and estimates are free.
Our Service Area Near Enterprise
We serve Enterprise and the surrounding valley, including chimney repair customers in Paradise, Henderson, Sunrise Manor, North Las Vegas and Las Vegas. We also cover Boulder City, Spring Valley, Sandy Valley and Mount Charleston, where the higher elevation and colder winters make a solid liner and insulated flue especially important. Response times depend on the route and the season, so we confirm scheduling when you book. The same crew that inspects your chimney does the repair, whether you’re close in or up toward the mountain.
If you’re nearby but a little outside the entry points above, call and we’ll confirm coverage before you book.
Serving Enterprise, NV – Our Local Coverage Area
We serve Enterprise and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Enterprise
Chimney repair is fixing the parts of the chimney that keep it safe and watertight, from the cap and crown to the flashing, liner and masonry. It ranges from a quick cap replacement to a new liner or a partial rebuild of the stack. We handle all of it in one place, so a sweep, repair and inspection don’t require separate contractors. The goal is a chimney that’s built to last, not just good enough to pass a look-over.
Most small repairs, like a cap or a crown, can be done in a single visit. Liner installation and masonry rebuilding take longer, sometimes a day or more depending on the flue and access. We give you a realistic timeline with the written estimate so you can plan around it. If a job needs a return visit, we tell you upfront rather than at the end.
Common repairs run $250 to $1,500, while liner installation typically runs $2,200 to $5,500 and masonry work between $500 and $2,500. The exact number depends on the height of the flue, how much needs work, and whether a liner or crown is involved. Your free estimate gives you a line-item price before any work starts. Call (855) 752-5896 for an exact quote; estimates are free.
Yes. We install and service DuraFlex flexible liner systems and apply HeatShield flue resurfacing, and we fit Gelco chimney caps. We also work with Famco ventilation components and Copperfield specialty parts. If your chimney has any of these products, or a different make entirely, we can help.
Same-day service is possible, and dispatch runs 7am to 7pm, Sunday through Friday, with Saturday closed. Call (855) 752-5896 and we’ll book you into the next opening. We answer 24/7, so a call outside dispatch hours gets booked into the next available slot. We don’t promise a same-day window until we confirm it against the schedule.
Our work is backed by the materials we specify and by our satisfaction guarantee on the work performed. Because we use professional-grade lines like DuraFlex and HeatShield, the products carry their own manufacturer-backed performance. We’ll spell out what’s covered in writing along with the estimate. Trust the materials and the crew, and we stand behind both.
Clear the area around the fireplace or stove and make sure we can reach the roof side if the repair is up there. Let us know if you have a gas appliance connected, since that changes how we approach the flue. Have any past inspection reports handy if you have them. Beyond that, the crew handles the setup and cleanup.
Schedule Your Chimney Repair Service in Enterprise Today
If something on your chimney has shifted, cracked or rusted through, don’t wait for the next storm to find out how bad it is. Call (855) 752-5896 to book a sweep and inspection, and we’ll give you a no-obligation estimate with camera evidence of what needs fixing. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. The team at Chimney Sweep Enterprise handles sweep, repair and inspect as one specialist, so you’re never coordinating three contractors. Built to last, not just to pass inspection.
Written by the team at Chimney Sweep Enterprise.